Buying guide

How to Choose a Push-To Telescope System

Updated on · By the Telescope Junkies team

A good push-to telescope system matches your mount's axes, holds alignment after setup, and points you close enough to find the target in your finder or low power eyepiece. Most buyers should pick encoder resolution, mounting brackets and software support before they compare brands.

On this page (11 sections)
  1. What a push to telescope system actually does
  2. How encoder and pointing system options differ
  3. Which manual mounts can take a push-to kit
  4. How pointing accuracy works in real use
  5. What software and sky maps you will use
  6. How much accuracy do you need for different targets
  7. Push-to systems compared with GoTo and star hopping
  8. How to install and align a push-to kit
  9. Common mistakes to avoid with push-to pointing
  10. Which push-to system should you buy for your mount
  11. How to care for encoders and keep pointing accurate

A good push-to telescope system turns a manual mount into a guided finder you move by hand. You select an object on a phone or laptop, then push the tube while the screen shows how far to move on each axis.

Encoder quality, bracket fit, alignment steps and software support decide whether you find a target in seconds or hunt for it in the dark. This guide compares those parts so you can match a kit to your mount and your skill level.

What a push to telescope system actually does

A push to telescope system does not move your telescope for you. Encoders count rotation on the azimuth and altitude axes, or on right ascension and declination for an equatorial mount.

Software turns those counts into a position on a sky map.

You choose a target, such as a planet, star cluster or galaxy. The screen shows arrows or numbers for each axis.

You push the tube by hand until both readings reach zero. Then you look through the eyepiece.

This approach keeps the mount manual and light. You avoid motors, batteries and tracking setup.

You also keep the tactile feel of a manual mount, which many observers prefer for visual use.

Accuracy depends on more than the encoder count. A solid mount, a careful alignment and a wide enough eyepiece field all help.

A push-to kit cannot fix a wobbly tripod or a loose tube ring.

52 Rule: buy push-to to find objects faster, not to track them. If you need tracking for long exposures, look at a motorized mount instead.

How encoder and pointing system options differ

Encoder and pointing system options fall into a few clear groups. Some kits add encoders to your existing mount.

Others replace the mount head with a computer controlled head. A few use a phone app and a simple sensor on one axis.

Encoder resolution is the most quoted spec. It describes how many steps the encoder reports per full rotation.

Higher resolution can give finer pointing, but only if the mount moves smoothly and the software uses the data well.

Mounting method matters just as much. A kit that clamps or bolts to existing shafts usually installs faster.

A kit that needs drilling may point well but risks damage if you misplace a hole. Check the manual before you start.

Encoders added to a manual mount

This is the classic push-to route. You keep your current mount and add sensors to its axes.

The kit may include brackets, cables and a hand box or a Bluetooth adapter for a phone.

The benefit is cost and simplicity. You keep a mount you already trust.

The trade-off is fit. Brackets must match your mount, and altitude motion can be awkward on some designs.

A new computerized mount head

A computerized head replaces the manual head and adds motors as well as pointing. It can slew to a target and track it.

That is more than push-to, but it helps you compare what push-to cannot do.

Our guide to best goto telescope mounts shows that full GoTo route. Open it if you want tracking, camera use or one button slews.

Stay with push-to if you want to keep your manual mount and learn to move it yourself.

53 Rule: pick the option whose brackets and software fit your mount today, not the option with the biggest encoder number.

Which manual mounts can take a push-to kit

Most manual mounts can take encoders in principle. Fit in practice depends on shaft access, space around the axes and room for cables.

Alt-azimuth and equatorial mounts each raise different issues.

On an alt-azimuth mount, the azimuth axis is usually easy to reach. The altitude axis may sit close to the tube or the tripod head.

Brackets must clear the tube through its full range. Test the full motion before you tighten final bolts.

On an equatorial mount, the right ascension axis often gives a clean place for an encoder. The declination axis can be tighter, especially near the counterweight shaft.

Cable routing must avoid snagging during polar alignment and meridian flips.

Mount size also matters. A small mount may lack room for brackets.

A larger mount may need a stronger bracket to resist flex. Flex in the bracket shows up as pointing error that changes with telescope position.

Load capacity matters too. Push-to does not add weight capacity.

A mount that already shakes under your tube will still shake. Encoders only report motion.

They do not stiffen the mount.

Our telescope mounts buying guide explains load, tripod and head choices in more detail. Read it if you are unsure whether your current mount is a good base.

54 Rule: confirm bracket fit for your exact mount model before you buy, and keep the mount's rated load in mind.

How pointing accuracy works in real use

Pointing accuracy is the gap between where the screen says you are and where the telescope actually points. A small gap is fine if your eyepiece field is wide.

A large gap can leave a faint galaxy outside the view.

Alignment sets the starting point. You point at two or three known stars and tell the software where you are.

The software then corrects for small errors in level, polar alignment and encoder zero points.

Tube flex and mount flex add error after alignment. A heavy tube can sag as it moves.

A loose dovetail or ring can shift the optical axis. Those errors change as you move across the sky.

The best test is the field of view. A low power eyepiece with a wide field forgives small errors.

A high power eyepiece with a narrow field does not. Match your accuracy needs to the eyepieces you actually use.

55 Rule: judge a system by how close it lands in your lowest power eyepiece, not by a lab number alone.

What software and sky maps you will use

Software turns encoder counts into a usable sky map. The best system for you depends on your phone, laptop and the objects you like to find.

A phone based system is portable and simple. You mount the phone near the eyepiece and read the direction arrows in the dark.

Check battery life and screen brightness controls for night use.

A laptop based system may offer a larger database and better planning tools. It can show the field of view for your telescope and eyepiece.

That helps you choose a bright star to start from and then hop to a faint target.

Look for support for common planetarium apps. Open standards make it easier to switch phones or laptops later.

A locked app can become a problem if support ends.

Object lists matter for your interests. Visual observers want Messier objects, planets and bright double stars.

A good list for one use may be poor for the other. Check how the software handles time and location, as correct site and time data prevent later errors.

56 Rule: choose software you will actually run at the eyepiece, with your phone or laptop, under a red light.

How much accuracy do you need for different targets

Bright targets need less accuracy. The Moon, Jupiter and bright clusters fill a wide field and show up even with a rough alignment.

Push-to pointing feels easy with those finds.

Faint galaxies and small planetary nebulae need more care. Their fields are smaller and their contrast is lower.

You may land nearby on a bright star and then star hop the last step.

Double stars and variable stars sit in between. Their fields are often moderate, but the target may be small.

A refined alignment with two or three stars helps a lot here.

Planets move and need current positions. Software with fresh ephemeris data helps.

Old data can leave the planet off center even if the mount pointing is correct. Your eyepiece choice sets the bar, so start at low power and only then increase magnification.

57 Rule: buy accuracy for the faintest target you plan to find, then use low power first until you master alignment.

Push-to systems compared with GoTo and star hopping

Push-to sits between star hopping and full GoTo. Star hopping uses a finder and a paper star chart.

GoTo moves the telescope and tracks. Push-to shows you where to move and leaves the motion to you.

For learning, push-to has a clear value. You learn how the mount moves and how the sky turns.

Those skills help even if you later buy a GoTo mount.

For speed, GoTo wins. It slews in seconds and tracks for photography.

Push-to needs your hands and your attention on every move. It also needs a fresh alignment if the mount is bumped.

For cost and weight, push-to often wins. You keep a manual mount and add a kit.

You avoid larger power supplies and heavier heads. That matters for travel and for small cars.

A diy telescope goto mount project can cost less than a ready made GoTo head, but it takes time and skill. Push-to kits usually install faster and need less wiring.

58 Rule: pick push-to for learning and light travel, pick GoTo for tracking and speed, keep star hopping as a backup skill.

How to install and align a push-to kit

Install starts with a clean, level mount. Tighten all locks and check that the tripod legs sit firm on the ground.

A shaky base will ruin pointing no matter how good the encoders are.

Fit the brackets without forcing them. Many kits use clamps or set screws that need even pressure.

Tighten a little, move the mount through its full range, then tighten again. Make sure cables do not pull as the tube moves.

Mount the encoders so they turn freely with the axes. There should be no grinding, binding or loose play.

A small gap in a coupling can cause jumps in the reading.

Power the system and check that both axes count in the right direction. Move the tube slowly and watch the screen.

If an axis counts backward, the software usually has a setting to reverse it.

Then run alignment. Point at a bright, known star and center it in the eyepiece.

Tell the software that star's name. Repeat with a second star in another part of the sky.

A third star improves accuracy.

59 Rule: install for free motion and repeat the same alignment routine every night until it becomes habit.

Common mistakes to avoid with push-to pointing

One common mistake is skipping the level check. A tilted tripod tilts the whole pointing model.

The error grows as you move away from the alignment stars. Level the tripod before you start.

Another mistake is trusting a single alignment star. One star sets a rough position, but two or three stars correct tilt and axis errors.

Always use at least two, and three if the kit allows it.

A third mistake is chasing high magnification too soon. High power shows every pointing error.

Find the target at low power first, center it, then increase power in steps.

Loose rings and dovetails also cause trouble. A tube that shifts in its rings points off after every move.

Tighten rings and dovetail knobs, then check again after a few moves.

Cable drag can pull the tube as you move. Route cables with slack and secure them so they do not tug on the encoders.

Poor night vision hurts too, so lower screen brightness and use a red filter if the app allows it.

60 Rule: fix level, alignment stars, tube tightness and screen brightness before you blame the encoders.

Which push-to system should you buy for your mount

Your mount decides the short list. Start with the exact mount model, then look for kits that name that model or show matching shaft and bracket photos.

Generic fit claims need a careful check.

If your mount is a small alt-azimuth, look for a light kit with simple brackets. Our best telescope tracking mount guide helps you judge small mount stability before you add sensors.

If your mount is a manual equatorial, look for encoders on both axes and clear cable routing. The Celestron CG-4 manual German equatorial mount in the box above shows the manual slow motion style that push-to kits often upgrade.

It supports up to 20 lb of optical equipment, but push-to does not raise that limit.

If you want tracking as well as pointing, compare a computerized head. The Celestron Advanced VX computerized German equatorial mount supports up to 30 lb, has a 40,000 plus object database and sidereal, solar and lunar tracking rates.

That is a GoTo step, not a pure push-to kit, and it weighs 47 lb as a full kit.

If you plan to do phone photography at the eyepiece, consider how you will capture the find. The MOVE SHOOT MOVE tridaptor in the box above is a 3-axis phone adapter for eyepieces from 0.86 to 2.4 in.

It helps you photograph what push-to finds, but it does not point the telescope.

For beginners still choosing a first telescope, read How Do I Know What Telescope to Choose? What to Know.

It helps you match tube size to mount strength. You can also use our How to Choose a Telescope for Beginners: A Simple Guide if you are new to the hobby.

If you pick a small smart telescope instead, a sturdy tripod still matters. Our best tripod for seestar s30 pro guide covers that separate need.

If you go the GoTo route later, a skywatcher az gti firmware update guide shows how firmware updates work on a computerized mount.

61 Rule: buy the kit that fits your mount, matches your targets and works with the phone or laptop you already own.

How to care for encoders and keep pointing accurate

Keep encoders clean and dry. Dust on a shaft or sensor can cause uneven counts.

Store the mount with covers if it lives outside or in a garage with grit.

Check bracket tightness before each session. Vibration in transport can loosen set screws.

A loose bracket may still move the mount, but readings will jump.

Balance the tube before you align. A badly balanced tube forces you to hold it as you move.

That extra force can flex the mount and shift the reading.

Recheck alignment after any bump. A knock to the tripod, a slipped ring or a moved counterweight changes the model.

Two fresh alignment stars can restore accuracy in minutes.

Keep firmware and star data up to date on your phone or laptop. Old planet positions cause more errors than most users expect.

Update on a schedule, not right before a session.

Our score weighs specs, features and buyer feedback against what you are shopping for. For this guide, we weighed encoder fit, pointing accuracy, software support and ease of install against the needs of manual mount owners.

Pick a kit that fits your mount, align with two or three stars, and start at low power. You will learn the sky faster than with any chart alone, and you will keep a mount that stays light and simple.

Frequently asked questions

What is a push-to telescope system?

A push-to telescope system uses encoders on your mount axes and a phone or laptop sky map to tell you where to move the telescope by hand. You push the tube toward the target while the screen shows direction and distance.

It finds objects without motors or tracking.

Are push to telescope systems accurate enough for faint objects?

Accuracy depends on encoder resolution, a firm mount, correct alignment and a small enough target field. Push-to pointing often lands within the field of a low power eyepiece or finder.

Faint galaxies and small nebulae may still need star hopping from a bright nearby star.

Can I add push-to to any manual telescope mount?

Many manual mounts can accept encoders, but bracket fit, axis access and cable routing vary by model. Check that the kit names your mount or shows the same shaft sizes and mounting points.

Some mounts need drilling or a third party bracket, so confirm before you order.

Is push-to better than GoTo for beginners?

Push-to can suit beginners who want to learn the sky and keep a simple manual mount. GoTo suits buyers who want tracking and one button slews.

Push-to teaches you to move the mount and read the sky, while GoTo does the pointing work for you.

What encoder resolution do I need?

Higher resolution gives smoother, more precise pointing, but very high numbers do not fix a flexing mount or poor alignment. Look for encoders that report small steps on both axes and a system that lets you refine alignment with two or three stars.

Real pointing accuracy matters more than the headline count.